Need a new backup camera for 1998 Marathon

My backup camera has stopped working and I need a replacement. The backup camera is in the back closet and shines through a piece of plexiglass in the back wall.

Unfortunately, technology has moved forward and I cannot find an easy replacement.

All the good (i.e., good image quality and low light performance) backup cameras have IR, which does not work in my application because the IR reflects off the plexiglass and effectively blinds the camera at night.

The cameras I have found without IR are low quality with CMOS sensors and thus have very poor low light performance.

The other complication is that the existing wiring is BNC with separate power leads whereas most modern cameras have video and power over the same cable. Adapters are available for some cameras, but not all.

Has anyone else tackled this issue?

Thanks,
Killeen

Kileen
I had the same issue, so I put a hole in the plexiglass and used a IR camera.
GregM

http://www.rearviewsystems.com/
I have used these people for a few projects and they are very helpful and good pricing!

Killeen,

Welcome to POG. Save yourself some typing by putting your coach information in as part of your signature. That way you don't have to put 1998 Marathon in each of your post headings. So far I have not had to repair/replace my back-up camera. I am however, working on a couple of other projects right now.

I used this outfit, Tim was very helpful and had adapters to use my older cables. I replaced the plexi port with aluminum sheet and mounted the camera outside.
http://www.rvcams.com

Will, How is your generator running ? Does it start and run on the first or second try ?

Jim,

Yes, and that is thanks to you and Miles. Carole and I can't possibly thank you two enough but we will try! Now if I could just figure out why I'm toasting the OTR A/C compressor clutch. It has progressed to a constant state of short cycling so finding the culprit should be easier - that is for someone with knowledge of these systems that is not electrically challenged!

I just replaced ours in our '98 Vantare and was lucky enough to just have to replace the camera..All the existing wiring was in the rear closet.. only took an hour to do. check out this one.. great color.. picture & price ... the old one was a CCD and very distorted. and without the night vision. I was able to use the existing video cable (I did have to buy an RCA adapter for the video cable) and the power supply was in the closet too so a very easy installation. I also put in a new 10" lcd monitor (built into the dash) to replace the old one and with making a new bezel (at the local sign shop) I was able to use the nice burl wood trim that was around the original monitor. check out the link below.. Backing up at night is a breeze.. its very bright and clear. I am very happy with mine. I didn't want to share a screen with the navigation system.. I like to see the toad all the times on a dedicated screen. Total cost with monitor about $250. I got the monitor on Amazon. http://www.rearviewsafety.com/accessories/rvs-771.html. :-)

Thanks for the suggestions.

I finally found a good CCD camera without IR at rvcams.com (the site recommend by jimblu). The camera was easy to install and wire up.

The camera model number is CH-Kit and was about $130 for the camera and wiring adapter. This camera has a 1/4 inch Panasonic sensor, 1 lux sensitivity, and a field of view that is 104 degrees horizontal and 78 degrees vertical.

Quote:

---

Originally Posted by jimblu

I used this outfit, Tim was very helpful and had adapters to use my older cables. I replaced the plexi port with aluminum sheet and mounted the camera outside.
http://www.rvcams.com

---

jimblu, would you please post a picture of your camera installation, for clarification of what you did and how it looks from outside.

Thanks, JIM

The b&w backup monitor in my dash is a "Intec cvm600". Has anyone found a replacement for this monitor? Or possibly replaced the camera and monitor and reused the existing cable? I believe my monitor and/or camera are going bad and will need to be replaced in the near future. Any suggestions on the best and/or easiest way to replace them? I am having trouble wrapping my head around the cable requirements of the new systems I see on line vs. the cable I have now.

Andre,
Contact Tim at RV Cams. He has helped me sort out back up camera issues on both of our buses. http://www.rvcams.com/default.htm.

On our Royale we replaced the original monitor with a Kenwood DNX8120 radio/XM/GPS unit. It has an input for a back up camera complete with a reverse switch sensing wire. In our case I used the original camera and wired the reverse switch wire to a toggle switch going to a 12volt source. Works great.

Brian,

Thanks, it is now on the list of things to do.

Replaced my camera last year with one from RVCams.com
CH-Kit which is a Color Waterproof CCD Camera "CH-77LAN"
It was an easy replacement and works well.
As a side note, when I removed the original camera the lense was loose.
A little tightening may have been all I needed to do?